How To Polish Aluminum Wheels With Clear Coat

They are less aggressive than the ones that are made for bare aluminum wheels. After you clean the wheel thoroughly, polish the aluminum and reapply the clear coat.

ZX3P Performance wheels, Alloy wheel, Racing

Same thing with the snowflakes the beast rides on.

How to polish aluminum wheels with clear coat. Most polished aluminum i've seen clear coated seems to loose some of the shine. Used a third of a can of kleen strip and brushed for 2 hours with little effect. We must make sure our lug nuts and weights.

Our goal in this particular discussion is to let you know how to remove a clear coat without necessarily damaging the underlying paint. Pick your choice of polishers and continue. The clear coat can be repaired in just a few hours to get your wheels looking nice and bright again.

After i detailed and waxed it in may of 2003, i waxed the polished wheels and have not waxed them again since. Nothing is removing the old clear. I've had my aluminum cross rams sanded, wheeled, and buffed and then clear coat powder coated.

Sprays work best for wheels, since the awkward shapes of some spokes make it a nightmare to get a brush in. I've put 10,000 miles on my '03 coupe with factory polished wheels since april 2003. This is enough time to let it dry really well.

All polished aluminum wheels from gm are absolutely clear coated, including the v. As a guy who used to polish aluminum for a living. Aluminum wheels are coated with a layer of clear coat paint for protection and added shine.

I picked up a set of used american racing aluminum wheels for cheap. This will prevent particles from getting in the way of sanding and assist in. Then fix the scratches as described above.

No loss of reflection and the coating is crystal clear. I'll probably wax them again sometime this winter. Aluminum is a soft metal that is more dull than most other types, so clear coat on aluminum wheels can eventually become dull or develop a yellow film that can make the wheels look old or dirty.

All of the above steps work great, if your wheels are bare aluminum. The addition of a clear coat of paint adds a layer of protection. Wipe the wheels with wax and grease remover and a microfiber towel.

Make sure to get it all off. A solution to clear coating wheels is a clear ceramic coating. That is how march sells there brackets and pulleys.

Finish by recoating the entire wheel with a new layer of clear coat specifically designed for wheels. If your clear coat is peeling, cracked, or chipping off, the only way to fix that is by stripping with paint and clear coat remover. Clear coat is mostly gone but i need to remove the rest so i can polish them.

I've tried acetone, lacquer thinner, kleen strip and carb cleaner. Not hard to apply at all either. Here's an excerpt from a technical.

Refinish aluminum wheels clear coat. This coating also does not yellow, grey or blue over and is very thin meaning a polished wheel stays nice and bright. You can probably successfully do a lacquer or single component clearcoat directly on your polished surface as long as it's spotlessly clean.

There are products out there that are specifically made for polishing coated wheels. Embed themselves into the substrate so no liquid contamination occurs even if the coating is scratched or broken. #2 nov 11, 2004.

Once the spray paint is fully dry to the touch, go ahead and slowly start peeling off the tape, the rims looks a hell of a lot. I learned this when i tried to clear an alt. Wipe the surface free of dust with a microfiber cloth.

Here is how youll polish coated wheels: I have a set of alum sport wheels on a 99 kia sportage 4x4 that the clear coat is coming off (they look terrible imo) i was gona strip as willys suggested, and repaint alum silver color and clear coat with urethane clear, or if the alum finish looked good after the chemical striper, i would just clear coat with urethane clear, but the machine / welding shop here made a oven a does power. If anyone posts up that theirs are not, it's because someone (a dealer, a detailer, or themselves) used something overly abrasive to clean the wheels and stripped the clear.

Still, some people swear that certain ano shops can pull off a clear ano that doesn't dull the surface. Obviously, the process of removing corrosion from aluminum wheels is. My little scamp pickup has had all the aluminum window and door moldings dipped to remove the anodizing, then highly polished, and then clear coat powder coated too.

As far as shooting clear, my opinion is that the surface finish of the metal is so fine the clear can't grab it. To remove a clear coat, you need a paint stripper product. Bare polished aluminum would oxidize within weeks.

There is no tooth for the clear to grab on to. It tends to look a little cloudy for a lack of a better word. I have yet to see it.

Our "new" (sort of) Matte Gold powder coat is now