How To Use A Toilet Snake Auger

Snakes are relatively small tools that are designed for the smaller pipes in your house. In most cases, the clog now flushes onward through the toilet and into the drain system.

FlexiSnake Drain Millipede Hair Clog Tool for Drain

The main difference between a toilet auger and a snake is the size of the tool.

How to use a toilet snake auger. Firmly grasp the shaft of the toilet auger. For this, if the clogging is at a great spread then you should use a toilet auger. The main difference between a toilet auger and a snake.

Auger is used to unclogging or removing obstacle what may cause stopping of the debris of the toilet to flow. When it cant turn any more, push the cable forward. Insert the toilet auger down the vent stack and start cranking the handle clockwise while pushing it down.

Place the end of the auger into the toilet bowl so that it points down the drain. You should feel the auger grab something or break up the clog. Pull the auger cable or snake all the way up until it reaches the bowl guard/elbow.

An electric snake is usually for drains, which are smaller in diameter. Place the auger into toilet bowl with the curved portion of the crank facing into the drainpipe. If not you will need to use the auger.

However, there are some key details you should observe. The steps for how to use an auger on a toilet start by rotating a cable until it moves into the drain opening. And last but not least is the head of the auger.

This means they are effective in pretty much any drain. Push the toilet auger cable through the toilet drain cranking the auger in a clockwise position. Make sure the head of the auger does not scratch against the porcelain toilet.

Place the end of the auger into the toilet bowl so that it points down the drain. If you find clogs at the top that you can easily pick up with your hand go ahead and do it. A toilet auger is much bigger because its meant for trapways.

Baking soda is not the cure all for your toilet clogs. Once the plumbing snake reaches the blockage, the auger will rotate within the drain. They can be powered with a cordless drill or you crank them by hand.

Climb to the top of the house roof using a ladder with the toilet auger to check the condition of the vent. For most augers, the cable is released from the bottom end of a long pole, and on the other end (at the top), there is a handle. Once inserted into the drain, you rotate the handle to extend the coil.

Operating either an auger or snake is relatively similar. Prepare the area around the toilet for any likely mess. The toilet auger does it more efficiently than the toilet plunger.

You do this by sliding the auger end of the device into the blocked drain. A toilet auger, also referred to as a toilet snake, is a toilet unclogger tool that is more powerful than a regular plunger. Most drain snakes are around 50 feet long.

Tighten the set screw on the auger when this length has been obtained. How to snake a toiletstep 1: After the auger is removed from the toilet drain, use a plunger to break up any final clogs and flush the toilet.

Once the cable has forced through the clog, pull the toilet auger out of the toilet by rotating the handle and pulling backward. Next part of the auger is the bowl guard, which will also be discussed later. It will be laid on the very bottom of the toilet.

At that point, turn and pull the cable back out of the drain. Drain snakes, on the other hand, are smaller as they are designed for shower drains, sinks, and bathtubs. The head of the auger has the shape of a small spring.

You can do this by winding up the manual crank. Toilet auger, also known as plumbing snake is the best when dealing with toilet clogs. Insert the head of the snake into the toilet hole.

When it stops, push the cable forward. As for the auger cable, its other name is the snake. Its function is to capture the blockage to make it easier to unclog.

This is a long tool designed for toilets that has a cable on the end, which is meant to get into the toilets trap way and get rid of the clog. The crank cable is much thinner than a toilet auger. The actual handle should not go inside the drain only the cabling.

You dont want your hands to get splashed with toilet water! With the cable removed, flush the toilet to see if the clog has disappeared. After all, theyre both just flexible cabling.

As it winds down the toilet, it breaks down waste while pushing it out of the drain. Sign up for our newsletter Turn the handle clockwise to extend the auger's cable (or snake) down into the drain towards your clog.

On the other hand, toilet augers are designed for larger pipes and have a large tool at the end of the auger. A toilet auger is retractable into a plastic cover so that you don't have to touch the cable after its been in the nasty toilet. Most likely, the hot water is what's unclogging your toilet, not the baking soda/vinegar combo.

If you feel the toilet auger grab onto something or it breaks up the clog in the toilet drain, gently turn and pull the cable out of the toilet drain. Do not use force when using the auger as this can cause.

Fresh Ridgid K 3 toilet Auger Home Depot